Duralex Grey Oxide Primer is solvent based anticorrosive and protective primer. It is alkyd-based primer and suitable for light to moderate environment. Duralex Grey Oxide Primer is recommended for all interior and exterior metal surfaces including new and pretreated zinc and galvanized iron. It may also be applied on pretreated aluminum.
Duralex Grey Oxide Primer is recommended for all interior and exterior metal surfaces including new and pretreated zinc and galvanized iron. It may also be applied on pretreated aluminum.
| Appearance | Matt Finish |
|---|---|
| Color | Grey |
| Binder Type | Alkyd |
| Pigment Type | Light Fast Non-Lead Pigment |
| Solvent | Naphtha Petroleum |
| Application | Brush, Roller and Spray |
| Flash Point | 35°C |
| Cleaning | Clean all equipment with Duralex Universal Thinner immediately after use |
| Thinner | Duralex Universal Thinner |
| Thinning | 10 – 15 % |
| Coverage |
12 - 14 m2 / Liter / coat Actual Spreading rate depends on film thickness, surface porosity, imperfections, temperature or wastage. |
| Specific Gravity | 1.4 ± 0.02 |
| Volume Solids (Theoretical) | 50 ± 2% |
| No. of Coats | 1 |
| Wet Film Thickness | 70-80 μm / liter / coat |
| Dry Film Thickness | 35-40 μm / liter / coat |
| Packing | 3.64, 4, 14.56 and 20 Liters |
| Drying Information | 5°C | 15°C | 25°C | 35°C |
|---|---|---|---|---|
| Touch Dry | 4 hrs | 3 hrs | 2 hrs | 1 hrs |
| Hard Dry | 16 hrs | 14 hrs | 12 hrs | 8 hrs |
| Recoat | 16 hrs | 14 hrs | 12 hrs | 8 hrs |
Drying and recoat times are temperature, humidity and film thickness dependent.
Appropriate and good surface preparation significantly increases the top coat life and durability. Deploy skilled/experienced individuals for the application of paint. A few general instructions are given below.
New or Bare Surfaces: Surface to be painted must be dry, clean and free from all contamination. Wipe with Duralex Universal Thinner to remove dirt, grease and wax. Scuff with suitable sand paper to remove rust. Wipe with Duralex Universal Thinner and apply Duralex Grey Oxide Primer. Allow the surface to dry out completely, scuff the surface with suitable sand paper and dust off.
Galvanized and Aluminum Surfaces: New Galvanized and aluminum surfaces should be cleaned and degreased, then pre-treated with an appropriate pre-treatment primer to ensure good adhesion.
Previously Painted Sound Surfaces: Previously painted sound surfaces must be thoroughly rubbed down using a suitable sand paper and dust off. Remove all loose scale, defective paint and rust by thorough scraping and wire brushing. Spot prime with Duralex Grey Oxide Primer and allow the surface to dry out completely. Scuff with suitable sand paper and dust off.
Finishing: After surface preparation apply 2-3 coats of recommended Duralex top coat. Ensure complete drying between successive coats. Thinning ratio must be followed for application procedure.
Stir thoroughly before use
| Sequence | Products | No. of coats |
|---|---|---|
| Primer | Duralex Grey Oxide Primer | 1 |
| Finish | Recommended Top Coat | 2-3 |
Consult Duralex Paints representative for the system best suited for the surfaces to be paint
WARNING: Scrapping/sanding off previously painted surfaces may release lead dust or fumes. Lead is highly toxic; take protective measures thoroughly when rubbing off the old surfaces.
Note:
The information in this data sheet is not intended to be exhaustive; any person using the product for any purpose other than that specifically recommended in this data sheet without first obtaining written confirmation from us as to the suitability of the product for the intended purpose does so at their own risk. All advice given or statements made about the product (whether in this data sheet or otherwise) is correct to the best of our knowledge but we have no control over the quality or the condition of the substrate or the factors affecting the use and application of the product. Therefore, unless we specifically agree in writing to do so, we do not accept any liability at all for the performance of the product or for (subject to the maximum extent permitted by law) any loss or damage arising out of the use of the product. We hereby disclaim any warranties or representations, express or implied, by operation of law or otherwise, including, without limitation, any implied warranty of merchantability or fitness for a particular purpose. All products supplied and technical advice given is subject to our Conditions of Sale. You should request a copy of this document and review it carefully. The information contained in this data sheet is liable to modification from time to time in the light of experience and our policy of continuous development. It is the user's responsibility to check with their local representative that this data sheet is current prior to using the product.
The information provided in this data sheet is accurate and authentic to the best of our knowledge and based on standard tests. However results may vary due to possible variations in field conditions and application procedures.
